Dynacord H 2500 Manuel d'utilisateur Page 22
- Page / 148
- Table des matières
- MARQUE LIVRES
Noté. / 5. Basé sur avis des utilisateurs
PowerH SERIES
22 Owner’s Manual
Structure of the CONFIG menu
Entering the CONFIG menu is possible through pressing the ENTER button while the entry
>> CONFIG << is highlighted in the status display. The following provides detailed information about the
individual items of the configuration menu.
CONFIG/Power-On-Delay: The power amp’s currently set power-
on delay is shown. Pressing the ENTER-Taste button opens the
Set Power-On-Delay dialog box.
Using the Up/Down buttons in the Set Power-On-Delay lets
the user specify a delay in the range of 0 seconds to up to 6.35
seconds. Pressing the ENTER button again stores the previously
made setting and the display returns to the CONFIG menu.
CONFIG/Breaker Current: The actually set value of the current
that controls the Mains Circuit Breaker Protection is displayed.
The set current has to match the value of the power amp’s internal
fuse for the protection to work correctly. Please refer to the
explanations on page 32 for more details. Pressing the ENTER
button opens the Set Breaker Current dialog box where the
desired value for the breaker current can be set.
The valid value ranges depend on the power amp’s power supply.
Currents between 6 A and 40 A can be set when the power
amplifier is operated at 120 V. Currents between 6 A and 30 A can
be set when the power amplifier is operated at 220-240 V. Select
Factory 30 A or Factory 16 A for automatic setting
depending on the power amp’s power supply. Pressing the
ENTER button stores the selected current value in memory and
the CONFIG menu reappears on the display.
CONFIG/Show Event Log: The menu entry Show Event Log
leads to the EVENT LOG submenu. The individual entries in the
EVENT LOG menu are explained in detail in the paragraph
Structure of the CONFIG.EVENT LOG menu (see page 23).
CONFIG/Menu Display: The menu entry Menu Display leads to
the DISPLAY SETUP submenu. Each entry in the
DISPLAY SETUP menu is explained in detail in paragraph
Structure of the CONFIG/DISPLAY SETUP menu (see page 24).
NOTE:
Operating the power amplifier on a separately fused mains power line is recommended
only.
- OWNER’S MANUAL 1
- BEDIENUNGSANLEITUNG 1
- MODE D’EMPLOI 1
- CONTENTS 2
- MATIÈRES 3
- IMPORTANT SAFETY INSTRUCTIONS 4
- 1 Introduction 5
- 1.1 Welcome 5
- 1.2 Unpacking and Inspection 5
- 1.4 Features and Description 6
- Rear View 8
- 2.2 Operating Voltage 9
- PowerH SERIES 10
- 2.3 Mains Switch 11
- 2.4 Mounting 12
- 2.6 Groundlift 13
- PARALLEL 14
- SENSITIVITY/GAIN 15
- Audio Cabling 16
- Bi-Amp Cabling 17
- CAUTION: 18
- 3 Operation 19
- 3.1 Volume Control 19
- 3.2 Graphical LC display 19
- Structure of the CONFIG menu 22
- 3.4 Fan Cooling 31
- Power-On Delay and Softstart 32
- Advanced Thermal Protection 33
- HF-Limiter 34
- Installation Notes 36
- Controls and Connections 38
- 3 LOCK-LED 39
- 4 REMOTE CAN BUS Connection 39
- 5 STATUS LED 40
- 6 ADDRESS Selector Switch 40
- 7 CONTROL PORT 41
- 8 RS-232 Interface 41
- CAN Bus Principles 42
- System Examples 44
- Performance Specifications 45
- WICHTIGE SICHERHEITSHINWEISE 49
- WICHTIGE SERVICEHINWEISE 49
- 1 Einführung 50
- 1.1 Willkommen 50
- 1.2 Auspacken und Inspektion 50
- 1.3 Lieferumfang und Garantie 50
- 2 Installation 52
- Rückseite 53
- 2.2 Betriebsspannung 54
- 2.3 Netzschalter 56
- 2.4 Einbau 57
- 2.5 Kühlung 58
- 2.7 Anzeige der Betriebsart 59
- 2.8 Wahl der Betriebsart 59
- Audio Verkabelung 61
- 1, SHIELD 62
- Bi-Amp Verkabelung 63
- ACHTUNG: 64
- 3 Betrieb 65
- 3.2 Graphisches LC-Display 65
- Menüführung Endstufe 66
- Menüstruktur CONFIG 68
- Menüstruktur CONFIG.EVENT LOG 70
- Menüstruktur CONFIG.SERVICE 72
- Menüstruktur MODULE CONFIG 74
- 3.3 Anzeigen 76
- 3.4 Lüfter 77
- 3.5 Schutzschaltungen 77
- Power-On Delay und Softstart 79
- 4 Optionen 81
- Installationshinweise 82
- Bedienelemente und Anschlüsse 84
- 4 REMOTE CAN BUS-Anschlüsse 85
- 6 ADDRESS-Wahlschalter 86
- Remote-Control-Netzwerk 88
- Systembeispiele 90
- Leitungsspezifikation 91
- 1.1 Bienvenue 96
- 1.2 Déballage et inspection 96
- 1.4 Fonctions et description 96
- Interférences radio 97
- 2.2 Tension de fonctionnement 100
- 2.3 Interrupteur secteur 102
- 2.4 Montage 103
- 2.5 Ventilation 104
- 2.6 Mise à la masse 105
- ATTENTION : 106
- SENSIBILITÉ/GAIN 107
- Câblage audio 107
- 3 Fonctionnement 111
- 3.1 Contrôle du volume 111
- 3.2 Écran LCD graphique 111
- Status display 113
- EVENT LOG 113
- DISPLAY SETUP 113
- Structure du menu CONFIG 114
- CAN-Baudrate 120
- Audio-Input 120
- 3.3 Indications 122
- 3.5 Protections 123
- Protection Coupe-Circuit 124
- Protection Thermique Avancée 125
- Limiteur HF 126
- 4 Options 127
- 4.1 RCM-26 127
- Remarques sur l’installation 128
- IRIS-Net™ 129
- Commandes et connexions 130
- 3 Témoin LOCK 131
- 4 Connexion REMOTE CAN BUS 131
- 5 Témoin STATUS 132
- 6 Sélecteurs ADDRESS 132
- 7 PORT DE CONTROLE 133
- Principes du Bus CAN 134
- Exemples de systèmes 136
- Dimensions / Abmessungen 143
- Declaration of conformity 144
Produits connexes et manuels pour Récepteurs et amplificateurs Dynacord H 2500
(51 pages)
(12 pages)
(72 pages)© 2020, manymanuals.fr. Tous droits réservés | 3.079 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Commentaires sur ces manuels