Dynacord H 2500 Manuel d'utilisateur Page 27
- Page / 148
- Table des matières
- MARQUE LIVRES
Noté. / 5. Basé sur avis des utilisateurs
PowerH SERIES
Owner’s Manual 27
CONFIG/SERVICE/Last Log: Shows point in time and type of the
last entry in the event history. If service is needed, the code shown
here provides relevant detail of what might have caused the
malfunction for your Dynacord Service partner.
CONFIG/SERVICE/Module Signature: In the event of failure or
malfunction, the information shown here provides relevant detail of
what might have caused the malfunction for your Dynacord Service
partner.
CONFIG/SERVICE/Firmware Version: This menu item shows
version and date of the firmware that is actually installed in the
power amplifier.
Structure of the MODULE CONFIG menu
The MODULE CONFIG menu provides access to RCM-26 remote control module settings, which are
available from the LC display of the power amplifier. This menu cannot be accessed during operation of
the power amplifier. Accessing this menu is only possible when the power amp is switched off.
The following steps open the MODULE CONFIG menu:
1. If the power amplifier is powered on or in standby mode, use the mains switch on the front panel to
switch the power amp off.
2. Simultaneously press the and ENTER buttons and keep them pressed.
3. Use the power switch on the front panel to switch the power amplifier on.
The power amp enters standby mode and the MODULE CONFIG
menu appears on the display.
- OWNER’S MANUAL 1
- BEDIENUNGSANLEITUNG 1
- MODE D’EMPLOI 1
- CONTENTS 2
- MATIÈRES 3
- IMPORTANT SAFETY INSTRUCTIONS 4
- 1 Introduction 5
- 1.1 Welcome 5
- 1.2 Unpacking and Inspection 5
- 1.4 Features and Description 6
- Rear View 8
- 2.2 Operating Voltage 9
- PowerH SERIES 10
- 2.3 Mains Switch 11
- 2.4 Mounting 12
- 2.6 Groundlift 13
- PARALLEL 14
- SENSITIVITY/GAIN 15
- Audio Cabling 16
- Bi-Amp Cabling 17
- CAUTION: 18
- 3 Operation 19
- 3.1 Volume Control 19
- 3.2 Graphical LC display 19
- Structure of the CONFIG menu 22
- 3.4 Fan Cooling 31
- Power-On Delay and Softstart 32
- Advanced Thermal Protection 33
- HF-Limiter 34
- Installation Notes 36
- Controls and Connections 38
- 3 LOCK-LED 39
- 4 REMOTE CAN BUS Connection 39
- 5 STATUS LED 40
- 6 ADDRESS Selector Switch 40
- 7 CONTROL PORT 41
- 8 RS-232 Interface 41
- CAN Bus Principles 42
- System Examples 44
- Performance Specifications 45
- WICHTIGE SICHERHEITSHINWEISE 49
- WICHTIGE SERVICEHINWEISE 49
- 1 Einführung 50
- 1.1 Willkommen 50
- 1.2 Auspacken und Inspektion 50
- 1.3 Lieferumfang und Garantie 50
- 2 Installation 52
- Rückseite 53
- 2.2 Betriebsspannung 54
- 2.3 Netzschalter 56
- 2.4 Einbau 57
- 2.5 Kühlung 58
- 2.7 Anzeige der Betriebsart 59
- 2.8 Wahl der Betriebsart 59
- Audio Verkabelung 61
- 1, SHIELD 62
- Bi-Amp Verkabelung 63
- ACHTUNG: 64
- 3 Betrieb 65
- 3.2 Graphisches LC-Display 65
- Menüführung Endstufe 66
- Menüstruktur CONFIG 68
- Menüstruktur CONFIG.EVENT LOG 70
- Menüstruktur CONFIG.SERVICE 72
- Menüstruktur MODULE CONFIG 74
- 3.3 Anzeigen 76
- 3.4 Lüfter 77
- 3.5 Schutzschaltungen 77
- Power-On Delay und Softstart 79
- 4 Optionen 81
- Installationshinweise 82
- Bedienelemente und Anschlüsse 84
- 4 REMOTE CAN BUS-Anschlüsse 85
- 6 ADDRESS-Wahlschalter 86
- Remote-Control-Netzwerk 88
- Systembeispiele 90
- Leitungsspezifikation 91
- 1.1 Bienvenue 96
- 1.2 Déballage et inspection 96
- 1.4 Fonctions et description 96
- Interférences radio 97
- 2.2 Tension de fonctionnement 100
- 2.3 Interrupteur secteur 102
- 2.4 Montage 103
- 2.5 Ventilation 104
- 2.6 Mise à la masse 105
- ATTENTION : 106
- SENSIBILITÉ/GAIN 107
- Câblage audio 107
- 3 Fonctionnement 111
- 3.1 Contrôle du volume 111
- 3.2 Écran LCD graphique 111
- Status display 113
- EVENT LOG 113
- DISPLAY SETUP 113
- Structure du menu CONFIG 114
- CAN-Baudrate 120
- Audio-Input 120
- 3.3 Indications 122
- 3.5 Protections 123
- Protection Coupe-Circuit 124
- Protection Thermique Avancée 125
- Limiteur HF 126
- 4 Options 127
- 4.1 RCM-26 127
- Remarques sur l’installation 128
- IRIS-Net™ 129
- Commandes et connexions 130
- 3 Témoin LOCK 131
- 4 Connexion REMOTE CAN BUS 131
- 5 Témoin STATUS 132
- 6 Sélecteurs ADDRESS 132
- 7 PORT DE CONTROLE 133
- Principes du Bus CAN 134
- Exemples de systèmes 136
- Dimensions / Abmessungen 143
- Declaration of conformity 144
Produits connexes et manuels pour Récepteurs et amplificateurs Dynacord H 2500
(51 pages)
(12 pages)
(72 pages)© 2020, manymanuals.fr. Tous droits réservés | 0.239 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Commentaires sur ces manuels