Dynacord H 2500 Manuel d'utilisateur Page 41
- Page / 148
- Table des matières
- MARQUE LIVRES
Noté. / 5. Basé sur avis des utilisateurs
PowerH SERIES
Owner’s Manual 41
7 CONTROL PORT
The CONTROL PORT of the RCM-26 provides two control inputs, two control
outputs and reference connections for +5V and ground. The control inputs are
configurable via IRIS-Net™. They can be used for example for switching
between power on / standby modes, switching between presets or to control
parameters. The two control contacts IN1 and IN2 are internally connected via
pull-up resistors and carry +5V (open). The control inputs can be activated using
external switches, pushbuttons or relays to connect them to ground potential (pin 3). The two control
outputs OUT1 and OUT2 are open collector outputs, which are highly resistive in the non-active state (off).
In active state (on) the outputs are connected to ground. The control outputs are configurable via IRIS-
Net™ and are used to signal internal states. LEDs, indicators or relays can be driven directly. The +5V
reference connector provides voltage supply for connected components.
8 RS-232 Interface
The RS-232 interface is for interconnecting the RCM-26 module and multi-media control systems or facility
management systems. All parameters can be controlled and queried via RS-232 interface. Communication
is realized through the use of ASCII-protocol. Implementation of this protocol is rather simple.
Programming notes and a complete protocol description are included in the IRIS-Net™ documentation.
HIGH LOW Address
0 0 Stand-alone
0 1...F 1...15
1 0...F 16...31
2 0...F 32...47
3 0...F 48...63
4 0...F 64...79
5 0...F 80...95
6 0...F 96...111
7 0...F 112...127
8 0...F 128...143
9 0...F 144...159
A 0...F 160...175
B 0...F 176...191
C 0...F 192...207
D 0...F 208...223
E 0...F 224...239
F 0...A 240...250
F B...F reserved
Table 4.3: CAN addresses
CAUTION:
The maximally allowable current at the +5V output is 200 mA.
- OWNER’S MANUAL 1
- BEDIENUNGSANLEITUNG 1
- MODE D’EMPLOI 1
- CONTENTS 2
- MATIÈRES 3
- IMPORTANT SAFETY INSTRUCTIONS 4
- 1 Introduction 5
- 1.1 Welcome 5
- 1.2 Unpacking and Inspection 5
- 1.4 Features and Description 6
- Rear View 8
- 2.2 Operating Voltage 9
- PowerH SERIES 10
- 2.3 Mains Switch 11
- 2.4 Mounting 12
- 2.6 Groundlift 13
- PARALLEL 14
- SENSITIVITY/GAIN 15
- Audio Cabling 16
- Bi-Amp Cabling 17
- CAUTION: 18
- 3 Operation 19
- 3.1 Volume Control 19
- 3.2 Graphical LC display 19
- Structure of the CONFIG menu 22
- 3.4 Fan Cooling 31
- Power-On Delay and Softstart 32
- Advanced Thermal Protection 33
- HF-Limiter 34
- Installation Notes 36
- Controls and Connections 38
- 3 LOCK-LED 39
- 4 REMOTE CAN BUS Connection 39
- 5 STATUS LED 40
- 6 ADDRESS Selector Switch 40
- 7 CONTROL PORT 41
- 8 RS-232 Interface 41
- CAN Bus Principles 42
- System Examples 44
- Performance Specifications 45
- WICHTIGE SICHERHEITSHINWEISE 49
- WICHTIGE SERVICEHINWEISE 49
- 1 Einführung 50
- 1.1 Willkommen 50
- 1.2 Auspacken und Inspektion 50
- 1.3 Lieferumfang und Garantie 50
- 2 Installation 52
- Rückseite 53
- 2.2 Betriebsspannung 54
- 2.3 Netzschalter 56
- 2.4 Einbau 57
- 2.5 Kühlung 58
- 2.7 Anzeige der Betriebsart 59
- 2.8 Wahl der Betriebsart 59
- Audio Verkabelung 61
- 1, SHIELD 62
- Bi-Amp Verkabelung 63
- ACHTUNG: 64
- 3 Betrieb 65
- 3.2 Graphisches LC-Display 65
- Menüführung Endstufe 66
- Menüstruktur CONFIG 68
- Menüstruktur CONFIG.EVENT LOG 70
- Menüstruktur CONFIG.SERVICE 72
- Menüstruktur MODULE CONFIG 74
- 3.3 Anzeigen 76
- 3.4 Lüfter 77
- 3.5 Schutzschaltungen 77
- Power-On Delay und Softstart 79
- 4 Optionen 81
- Installationshinweise 82
- Bedienelemente und Anschlüsse 84
- 4 REMOTE CAN BUS-Anschlüsse 85
- 6 ADDRESS-Wahlschalter 86
- Remote-Control-Netzwerk 88
- Systembeispiele 90
- Leitungsspezifikation 91
- 1.1 Bienvenue 96
- 1.2 Déballage et inspection 96
- 1.4 Fonctions et description 96
- Interférences radio 97
- 2.2 Tension de fonctionnement 100
- 2.3 Interrupteur secteur 102
- 2.4 Montage 103
- 2.5 Ventilation 104
- 2.6 Mise à la masse 105
- ATTENTION : 106
- SENSIBILITÉ/GAIN 107
- Câblage audio 107
- 3 Fonctionnement 111
- 3.1 Contrôle du volume 111
- 3.2 Écran LCD graphique 111
- Status display 113
- EVENT LOG 113
- DISPLAY SETUP 113
- Structure du menu CONFIG 114
- CAN-Baudrate 120
- Audio-Input 120
- 3.3 Indications 122
- 3.5 Protections 123
- Protection Coupe-Circuit 124
- Protection Thermique Avancée 125
- Limiteur HF 126
- 4 Options 127
- 4.1 RCM-26 127
- Remarques sur l’installation 128
- IRIS-Net™ 129
- Commandes et connexions 130
- 3 Témoin LOCK 131
- 4 Connexion REMOTE CAN BUS 131
- 5 Témoin STATUS 132
- 6 Sélecteurs ADDRESS 132
- 7 PORT DE CONTROLE 133
- Principes du Bus CAN 134
- Exemples de systèmes 136
- Dimensions / Abmessungen 143
- Declaration of conformity 144
Produits connexes et manuels pour Récepteurs et amplificateurs Dynacord H 2500
(51 pages)
(12 pages)
(72 pages)© 2020, manymanuals.fr. Tous droits réservés | 0.806 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Commentaires sur ces manuels