Dynacord H 2500 Manuel d'utilisateur Page 23
- Page / 148
- Table des matières
- MARQUE LIVRES
Noté. / 5. Basé sur avis des utilisateurs
PowerH SERIES
Owner’s Manual 23
CONFIG/Menu Service: The menu entry Menu Service
branches to the SERVICE submenu. The entries in the SERVICE
menu are explained in detail in paragraph Structure of the
CONFIG/SERVICE menu (see page 26).
CONFIG/Amplifier Name: Displays the name of the power
amplifier. The menu entry only exists when no RCM-26 is installed
in the power amplifier. With a remote control module installed, the
power amplifier has to be named via IRIS-Net™. Pressing the
ENTER button opens the Set Amplifier Name dialog box.
The Set Amplifier Name dialog allows changing the power
amp’s name, which can be composed of a maximum of 20
symbols and consist of all letters a-z, A-Z, the numbers 0-9 and
special characters.
Pressing the Up/Down buttons locates the cursor at the desired
position of the name. Pressing the ENTER button accepts the
desired symbol and moves the cursor to the next character.
Pressing the ENTER button after manipulating the last character,
stores the desired name of the power amplifier in the memory and
the display returns to the CONFIG menu.
The following special characters provide special functions when entering a power amp’s name:
Structure of the CONFIG/EVENT LOG menu
CONFIG/EVENT LOG/Counter POWER UP: This menu item
shows how many times the power switch on the front panel has
been used.
CONFIG/EVENT LOG/Counter AMP ON: This menu item shows
how often the power amplifier has been activated from the OFF or
STANDBY state.
Character Function
↵ Accepts the entered name and returns to the menu.
A
Deletes the currently selected symbol and moves the cursor by one character to the right.
I
Set the cursor by one character to the left.
Table 3.2: Functions of special characters when entering the power amp’s name
- OWNER’S MANUAL 1
- BEDIENUNGSANLEITUNG 1
- MODE D’EMPLOI 1
- CONTENTS 2
- MATIÈRES 3
- IMPORTANT SAFETY INSTRUCTIONS 4
- 1 Introduction 5
- 1.1 Welcome 5
- 1.2 Unpacking and Inspection 5
- 1.4 Features and Description 6
- Rear View 8
- 2.2 Operating Voltage 9
- PowerH SERIES 10
- 2.3 Mains Switch 11
- 2.4 Mounting 12
- 2.6 Groundlift 13
- PARALLEL 14
- SENSITIVITY/GAIN 15
- Audio Cabling 16
- Bi-Amp Cabling 17
- CAUTION: 18
- 3 Operation 19
- 3.1 Volume Control 19
- 3.2 Graphical LC display 19
- Structure of the CONFIG menu 22
- 3.4 Fan Cooling 31
- Power-On Delay and Softstart 32
- Advanced Thermal Protection 33
- HF-Limiter 34
- Installation Notes 36
- Controls and Connections 38
- 3 LOCK-LED 39
- 4 REMOTE CAN BUS Connection 39
- 5 STATUS LED 40
- 6 ADDRESS Selector Switch 40
- 7 CONTROL PORT 41
- 8 RS-232 Interface 41
- CAN Bus Principles 42
- System Examples 44
- Performance Specifications 45
- WICHTIGE SICHERHEITSHINWEISE 49
- WICHTIGE SERVICEHINWEISE 49
- 1 Einführung 50
- 1.1 Willkommen 50
- 1.2 Auspacken und Inspektion 50
- 1.3 Lieferumfang und Garantie 50
- 2 Installation 52
- Rückseite 53
- 2.2 Betriebsspannung 54
- 2.3 Netzschalter 56
- 2.4 Einbau 57
- 2.5 Kühlung 58
- 2.7 Anzeige der Betriebsart 59
- 2.8 Wahl der Betriebsart 59
- Audio Verkabelung 61
- 1, SHIELD 62
- Bi-Amp Verkabelung 63
- ACHTUNG: 64
- 3 Betrieb 65
- 3.2 Graphisches LC-Display 65
- Menüführung Endstufe 66
- Menüstruktur CONFIG 68
- Menüstruktur CONFIG.EVENT LOG 70
- Menüstruktur CONFIG.SERVICE 72
- Menüstruktur MODULE CONFIG 74
- 3.3 Anzeigen 76
- 3.4 Lüfter 77
- 3.5 Schutzschaltungen 77
- Power-On Delay und Softstart 79
- 4 Optionen 81
- Installationshinweise 82
- Bedienelemente und Anschlüsse 84
- 4 REMOTE CAN BUS-Anschlüsse 85
- 6 ADDRESS-Wahlschalter 86
- Remote-Control-Netzwerk 88
- Systembeispiele 90
- Leitungsspezifikation 91
- 1.1 Bienvenue 96
- 1.2 Déballage et inspection 96
- 1.4 Fonctions et description 96
- Interférences radio 97
- 2.2 Tension de fonctionnement 100
- 2.3 Interrupteur secteur 102
- 2.4 Montage 103
- 2.5 Ventilation 104
- 2.6 Mise à la masse 105
- ATTENTION : 106
- SENSIBILITÉ/GAIN 107
- Câblage audio 107
- 3 Fonctionnement 111
- 3.1 Contrôle du volume 111
- 3.2 Écran LCD graphique 111
- Status display 113
- EVENT LOG 113
- DISPLAY SETUP 113
- Structure du menu CONFIG 114
- CAN-Baudrate 120
- Audio-Input 120
- 3.3 Indications 122
- 3.5 Protections 123
- Protection Coupe-Circuit 124
- Protection Thermique Avancée 125
- Limiteur HF 126
- 4 Options 127
- 4.1 RCM-26 127
- Remarques sur l’installation 128
- IRIS-Net™ 129
- Commandes et connexions 130
- 3 Témoin LOCK 131
- 4 Connexion REMOTE CAN BUS 131
- 5 Témoin STATUS 132
- 6 Sélecteurs ADDRESS 132
- 7 PORT DE CONTROLE 133
- Principes du Bus CAN 134
- Exemples de systèmes 136
- Dimensions / Abmessungen 143
- Declaration of conformity 144
Produits connexes et manuels pour Récepteurs et amplificateurs Dynacord H 2500
(51 pages)
(12 pages)
(72 pages)© 2020, manymanuals.fr. Tous droits réservés | 0.067 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Commentaires sur ces manuels