Dynacord H 2500 Manuel d'utilisateur Page 25
- Page / 148
- Table des matières
- MARQUE LIVRES
Noté. / 5. Basé sur avis des utilisateurs
PowerH SERIES
Owner’s Manual 25
Structure of the CONFIG/DISPLAY SETUP menu
CONFIG/DISPLAY SETUP/LCD Contrast: This menu item
indicates the currently set contrast of the LC display. Pressing the
ENTER button opens the Set LCD Contrast where the user
can select a contrast setting in the range of 0 % to 100 % by using
the Up/Down buttons. Pressing the ENTER button again stores
the selected value for contrast in memory and the CONFIG menu
reappears on the display.
CONFIG/DISPLAY SETUP/LCD Brightness: The currently set
maximum and minimum values for display brightness are
indicated. The maximum value represents the brightness of the
display that is used during normal operation. The minimum value
represents the brightness of the display that it is adjusted to after a
specific period of time, if desired.
Pressing the ENTER button opens the Set Brightn. Hi-Lvl
dialog box, which, by pressing the Up/Down buttons, allows
setting the undimmed display brightness in a range of 50 % to
100 %.
Pressing the ENTER button stores the set brightness value in
memory and the display indication changes to the
Set Brightn. Lo-Lvl dialog box, where pressing the Up/
Down buttons allows setting the dimmed display brightness in a
range of 0 % to 80 %. Pressing the ENTER button again stores
the set brightness value and the display returns to the CONFIG
menu.
CONFIG/DISPLAY SETUP/LCD Time to Dim: The currently set
time interval, during which the display lights with the maximum
brightness it has been set to, is indicated. After the time interval
has expired the display is dimmed.
Pressing the ENTER button opens the Set LCD Time to Dim
dialog box, where the user can specify the duration after which the
display dimming starts by pressing the Up/Down buttons. The
duration can be set to 4, 8, 16, 32 or 64 minutes. Alternately, the
user can select Autodim off to completely deactivate the
dimming function, which results in the display always lighting at
the set maximum brightness level (Brightn. Hi-Lvl).
For an increased lifetime of the display, activating the dimming
function is recommended. Pressing the ENTER button stores the
settings in memory and the display returns to the CONFIG menu.
- OWNER’S MANUAL 1
- BEDIENUNGSANLEITUNG 1
- MODE D’EMPLOI 1
- CONTENTS 2
- MATIÈRES 3
- IMPORTANT SAFETY INSTRUCTIONS 4
- 1 Introduction 5
- 1.1 Welcome 5
- 1.2 Unpacking and Inspection 5
- 1.4 Features and Description 6
- Rear View 8
- 2.2 Operating Voltage 9
- PowerH SERIES 10
- 2.3 Mains Switch 11
- 2.4 Mounting 12
- 2.6 Groundlift 13
- PARALLEL 14
- SENSITIVITY/GAIN 15
- Audio Cabling 16
- Bi-Amp Cabling 17
- CAUTION: 18
- 3 Operation 19
- 3.1 Volume Control 19
- 3.2 Graphical LC display 19
- Structure of the CONFIG menu 22
- 3.4 Fan Cooling 31
- Power-On Delay and Softstart 32
- Advanced Thermal Protection 33
- HF-Limiter 34
- Installation Notes 36
- Controls and Connections 38
- 3 LOCK-LED 39
- 4 REMOTE CAN BUS Connection 39
- 5 STATUS LED 40
- 6 ADDRESS Selector Switch 40
- 7 CONTROL PORT 41
- 8 RS-232 Interface 41
- CAN Bus Principles 42
- System Examples 44
- Performance Specifications 45
- WICHTIGE SICHERHEITSHINWEISE 49
- WICHTIGE SERVICEHINWEISE 49
- 1 Einführung 50
- 1.1 Willkommen 50
- 1.2 Auspacken und Inspektion 50
- 1.3 Lieferumfang und Garantie 50
- 2 Installation 52
- Rückseite 53
- 2.2 Betriebsspannung 54
- 2.3 Netzschalter 56
- 2.4 Einbau 57
- 2.5 Kühlung 58
- 2.7 Anzeige der Betriebsart 59
- 2.8 Wahl der Betriebsart 59
- Audio Verkabelung 61
- 1, SHIELD 62
- Bi-Amp Verkabelung 63
- ACHTUNG: 64
- 3 Betrieb 65
- 3.2 Graphisches LC-Display 65
- Menüführung Endstufe 66
- Menüstruktur CONFIG 68
- Menüstruktur CONFIG.EVENT LOG 70
- Menüstruktur CONFIG.SERVICE 72
- Menüstruktur MODULE CONFIG 74
- 3.3 Anzeigen 76
- 3.4 Lüfter 77
- 3.5 Schutzschaltungen 77
- Power-On Delay und Softstart 79
- 4 Optionen 81
- Installationshinweise 82
- Bedienelemente und Anschlüsse 84
- 4 REMOTE CAN BUS-Anschlüsse 85
- 6 ADDRESS-Wahlschalter 86
- Remote-Control-Netzwerk 88
- Systembeispiele 90
- Leitungsspezifikation 91
- 1.1 Bienvenue 96
- 1.2 Déballage et inspection 96
- 1.4 Fonctions et description 96
- Interférences radio 97
- 2.2 Tension de fonctionnement 100
- 2.3 Interrupteur secteur 102
- 2.4 Montage 103
- 2.5 Ventilation 104
- 2.6 Mise à la masse 105
- ATTENTION : 106
- SENSIBILITÉ/GAIN 107
- Câblage audio 107
- 3 Fonctionnement 111
- 3.1 Contrôle du volume 111
- 3.2 Écran LCD graphique 111
- Status display 113
- EVENT LOG 113
- DISPLAY SETUP 113
- Structure du menu CONFIG 114
- CAN-Baudrate 120
- Audio-Input 120
- 3.3 Indications 122
- 3.5 Protections 123
- Protection Coupe-Circuit 124
- Protection Thermique Avancée 125
- Limiteur HF 126
- 4 Options 127
- 4.1 RCM-26 127
- Remarques sur l’installation 128
- IRIS-Net™ 129
- Commandes et connexions 130
- 3 Témoin LOCK 131
- 4 Connexion REMOTE CAN BUS 131
- 5 Témoin STATUS 132
- 6 Sélecteurs ADDRESS 132
- 7 PORT DE CONTROLE 133
- Principes du Bus CAN 134
- Exemples de systèmes 136
- Dimensions / Abmessungen 143
- Declaration of conformity 144
Produits connexes et manuels pour Récepteurs et amplificateurs Dynacord H 2500
(51 pages)
(12 pages)
(72 pages)© 2020, manymanuals.fr. Tous droits réservés | 0.218 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Commentaires sur ces manuels